Rackmount Case Options
A broad range of standard options for our rackmount shipping cases
will allow you to adapt our Double-Entry cases to a wide variety
of transit applications.
- Airtight case system. Includes a pressure relief valve and gasketing
hardware to safely maintain correct pressure differential. Manual
release button is recessed below cover rim. Test pressure range
is +/- 0.25 PSID (18 mb)
- Bezel plate. Blank bezel plates in 16 gauge aluminum. Flanged
for strength. Brushed black anodized finish. Available in 1U,
2U, 3U, and 4U heights
- Cardholder. Metal holder for shipping-card riveted to the exterior
of case. Two sizes: 2-3/8" x 5-3/8" (60 x 136 mm) and 4" x 6"
(102 x 152 mm)
- Caster sets. Hardigg-engineered caster mounting system enhances
the bottom panel strength of rack cases, while providing the same
button release convenience of the FastClipÔ mounting plate
system found on Hardigg’s single-lid cases. These swivel
style casters are Colson or equivalent brand, available in removable
or fixed 3.5" or 5" wheel diameters. Includes four casters, two
machined aircraft aluminum extrusions, and mounting hardware installed
on the case bottom
- Caster store-in-lid system. Removable casters are securely stored
in lid using Hardigg FastClip mounting plate system. For 5" (127
mm) lids only
- Coupling catches. Elastomeric devices to couple vertically stacked
containers to prevent accidental tip over
- Drawers. 19" rackmountable drawers are 14" (356 mm) deep and
key-lockable. Complete with drawer slides. Available in 2U, 3U,
and 4U heights. [U = 1.75" (44.45 mm).]
- Foam cushioning. To transport non-rackmountable equipment, we
custom-design protective foam linings and inserts. Hardigg cushioning
systems are available in polyethylene (firmer) and polyurethane
(softer) foams. Antistatic versions are also available. This option
is a major element in equipping double-lid cases used to transport
workstations
- Frame option rack extension — 1/8" wider. Used when extra
clearance is necessary, usually to accommodate slides. Requires
slotted mounting holes in attaching bezel of equipment to be mounted
- Handles — extra. These 90° stop metal handles are
rated to sustain 150 lbs. of lift. Available in zinc-plate yellow-chromate
or stainless steel
 Humidity
indicator. Indicates 20%, 30%, and 40% relative humidity ranges.
Three-part face changes color when inside humidity exceeds the indicated
level. As humidity decreases, the indicator resets for future use.
Recommended for airtight cases only.
ID plates. I.A.W. MIL-P-15024, Type H, Style IV, Size 10.4"
x 4" x .020" (102 x 102 x 0.5 mm) thick aluminum, fastener attached
to your case. Text font is News Gothic Bold.
Keyboard tray. Accommodates standard size keyboard. 24"
(610 mm) wide, 12" (305 mm) deep. Attaches to case front catches.
Labels - front. To assure that lids are replaced in the
proper orientation. A set of two "front" labels is affixed to the
case, one on the midsection and one on the lid.
Lid hangers. Used to store lids conveniently on side of
case when case is open. A set of four hangers for two lids. This
option comes at no extra charge.
Lifting/tie-down rings. These welded rings provide hoisting
and tie-down attachment points with 2" (51 mm) diameter clearance
for hooks. They’re spring-loaded and pivot 180°. Available
in plated steel or stainless steel.
Locking cable/hasp. Allows the case to be padlocked shut.
Cable is tamper-resistant aircraft steel. Order two per lid. [Padlock
not included.]
Panel screws (with plastic washers). Used for mounting rack
units, drawers, and blank bezel plates. Set of 50; size is 10-32
x 7.5.
Rack frame/shock-mount guidelines for extra-heavy loads.
For rackmount cases with more than 170 lb. (77 Kg) of packaged equipment,
sixteen elastomeric shock mounts are used instead of the standard
eight. Vertical metal wall stiffeners are added to the case body
to retain dimensional control of the two openings and ensure that
the covers can easily go back on the case body and latch properly.
Four delta lifting/tie-down rings are also installed to provide
mechanical lift accessibility.
Rack slides. These compact solid-bearing steel slides may
be used to mount equipment directly into rack, or to mount drawers
or shelves. Sold in pairs. Available in standard duty, 85 pound
capacity.
Shelves - fixed and sliding. Shelves can be removed and
customized to accommodate non-rackmountable equipment.
Stainless hardware. Recommended for applications where the
standard zinc-plate or zinc alloy finishes are unsuitable, such
as excessive saltwater or chemical environments.
Stencil - epoxy or polyrollmark. Per MIL-I-43553. Available
in black, white, and yellow, depending on the color of the case
itself. One ink color per case.
Storage pouches. Zippered pouch for storing cables and accessories
in front or rear lids. Comes mounted in 5" lids. Three sizes: 10"
x 22" x 2.5" (254 x 559 x 63 mm); 16" x 22" x 2.5" (406 x 559 x
63 mm); and 18" x 18" x 2.5" (457 x 457 x 63 mm).
Support rails - bottom. Two each support rails used to support
equipment while installing heavy loads.
Support rails - side-adjustable. Two each 2" x 2" x 1/8"
(51mm x 51mm x 3mm) aluminum-angle, vertically-adjustable support
rails used to support equipment while installing heavy loads.
|
